L4S FrameBlasting Flow

{
   "type":  "l4s_frame_blasting",
   "name":  "<flow_name:str>",
   "source": {
         "port_group": [
            "<source_group:str>"
         ]
   },
   "destination": {
         "port_group": [
            "<destination_group:str>"
         ]
   },
   "l4s_ecn": "<l4s_ecn_marking_type:str>",
   "dscp": "<dscp_code_point:str|int>",
   "add_reverse_direction": "<add_reverse_direction_flow:bool>",
   "initial_time_to_wait": "<initial_time_to_wait:float|int|timedelta>",
   "bitrate": "<flow_bitrate:float>",
   "frame_size": "<frame_size_without_crc:int>",
   "frame_rate": "<frame_rate:float>",
   "number_of_frames": "<number_of_frames:float>",
   "duration": "<flow_duration:float|int|timedelta>",
   "udp_src": "<udp_source_port:int>",
   "udp_dest": "<udp_destination_port:int>",
   "nat_keep_alive": "<activate_nat_keep_alive:bool>",
   "analysis": {
      "latency":"<enable_latency_analysis:bool>",
      "max_threshold_latency": "<max_threshold_latency:float>",
      "max_loss_percentage": "<max_loss_percentage:float>",
      "quantile": "<quantile:float>",
      "min_percentile": "<min_percentile:float>",
      "max_percentile": "<max_percentile:float>"
   }
}

L4S frame blasting flow
Specific parameters for L4S frame blasting flow. The type MUST be defined as l4s_frame_blasting.
Note Not supported by ByteBlower Endpoint.
type	object
properties
type	l4s_frame_blasting
name	Name of this Flow, defaults to auto-generated name when set to none
	type	string
source	Specifying the source of transmitted data for this flow
	type	object
	properties
	port_group	List of port groups specifying the transmitting ports
		type	array
		items	Port group
	additionalProperties	False
destination	Specifying the destination for receiving data for this flow
	type	object
	properties
	port_group	List of port groups specifying the receiving ports
		type	array
		items	Port group
	additionalProperties	False
l4s_ecn	IP ECN
	Explicit Congestion Notification code point, defaults to DEFAULT_IP_ECN (0x00)
	oneOf	type	number
		type	string
dscp	IP DSCP
	Differentiated Services Code Point, defaults to DEFAULT_IP_DSCP (0x00)
	oneOf	type	number
		type	string
add_reverse_direction	Enables adding a flow in the reverse direction of the original flow with the same configuration, defaults to false
	type	string
initial_time_to_wait	Initial time to wait to start the flow in seconds, defaults to 0 (start immediately).
	type	number
bitrate	Rate at which the bits are transmitted in bits/s. Excludes the VLAN tag bytes (when applicable), mutual exclusive with frame_rate, defaults to none
	type	string
frame_size	Frame size in Bytes without CRC, defaults to none
	type	number
frame_rate	Rate at which the frames are transmitted (in frames per second), mutual exclusive with bitrate, defaults to DEFAULT_FRAME_RATE (100) when bitrate is not provided.
	type	number
number_of_frames	Number of frames to transmit, defaults to DEFAULT_NUMBER_OF_FRAMES (none == defined by scenario maximum run time).
	type	string
duration	Duration of the flow in seconds, defaults to none (use number_of_frames instead)
	type	string
udp_src	UDP port number in range [49152,65534] , defaults to udp_dynamic_port
	type	number
udp_dest	UDP port number in range [49152,65534] , defaults to udp_dynamic_port
	type	number
nat_keep_alive	Enable a flow to keep Network Address (and Port) Translation (NAT/NAPT) entries alive. The direction will be from the endpoint behind a NAT/NAPT gateway to the port at the public side of the NAT/NAPT gateway, defaults to false. We always enable the NAT/NAPT keep alive when the user asks for it, even when: the reverse flow is enabled and source and destination UDP ports are the same the source is the endpoint behind the NAT/NAPT gateway: An initial time to wait on the flow can still cause the NAPT entries at the gateway might still timeout before the traffic starts. This might cause the NAPT gateway to create a new (and maybe different!) NAPT entry, causing our traffic analysis to fail (with 100% loss).
	type	boolean
napt_keep_alive	Deprecated since version v1.1.0: Use nat_keep_alive instead. Will be removed in v1.3.0.
	type	boolean
analysis	Sets latency related analysis configuration parameters
	oneOf	Frame loss analysis parameters
		Latency & frame loss analysis parameters